XT60 / XT30 connectors (Y-splitter & adapters)
Typical 12 AWG XT60 1→3 power Y (~30 cm) — one pack to multiple loads
XT60H-M / XT60H-F with grey snap-on sheaths (as ordered)
Compact XT30↔XT60 adapters for bench / peripherals
Classic Amass XT60 pairs — solder with a chisel tip + flux: see tools
One pack. Three hungry loads. The temptation to solder a Y straight onto the battery lead was real — “saves a connector.” We didn’t. With the Tattu 6S and O4 Air Unit Pro we want proper XT60 harnessing: one pack, three branches, no mess on the battery itself.
We ordered:
- XT60H Y-splitter 12 AWG — 1 plug → 3 sockets, ~30 cm
- Extra XT60H male/female pairs + housings
- XT30↔XT60 adapters (2× XT30-male → XT60-female, 2× XT30-female → XT60-male)
Does that Y need to be exactly 30 cm? No idea until it sits on the frame. Better a bit long and trim than too short and reorder.
Role in the build
Pack XT60 (male on battery)
└──► Y-splitter female
├──► Pacer ESC (XT60)
├──► PM02D (often XT60 on board; else adapter)
└──► O4 Pro power leads (solder/adapter onto XT60 branch)
See power & capacitors · step 2.
Polarity & safety
- XT60/XT60H are polarized (+/− marked). Verify with a meter before first contact.
- Convention: female on the “live” source side where practical. Never assume with no-name cables.
- 12 AWG Y is fine for short branches. Keep joints clean. Soldering XT60: chisel tip + flux — tools · nanofix tip care.
- 6S hot-plug sparks. Props off. Anti-spark (XT90-S elsewhere) is a later maybe.
What do the five say?
No product review of our Y-splitter SKU — category advice on XT60 soldering / power.
| Reviewer | Found? | Takeaway | Link |
|---|---|---|---|
| Oscar Liang | yes (category) | XT60/thick power leads: high tip temp, bevel tip, 63/37 — no Y-splitter review | Soldering guide |
| Joshua Bardwell | yes (category) | Tools/solder videos: chisel tip + flux on XT60; no dedicated connector-kit review | Soldering tutorial |
| Chris Rosser | no review found | No XT60-Y product review found | — |
| Painless360 | yes (category) | Beginner series on soldering the power system — how, not which Ali Y | Soldering the power system |
| UAV Tech | no review found | No XT60 connector review found | — |
Our pick: 12 AWG XT60H 1→3 Y as the pack hub. Extra pairs for repair. XT30 adapters only for peripherals (smoke stopper, lab), not as a substitute for the Y to the ESC.
Manuals / datasheets
| Document | Local | Source |
|---|---|---|
| AMASS XT60 datasheet (M/F) | AMASS / distributor copy | |
| XT60H | Search AMASS XT60H (housed XT60 variant) | china-amass.com |
| Battery connector | — | Tattu pack |
| O4 power pins | — | O4 Pro part · DJI downloads |
No separate “manual” ships with generic Y cables. Use Amass ratings (XT60 ~60 A class depending on solder/wire) and our wiring post.
XT30 adapters — when
Only if a device has XT30 (small BEC, smoke stopper, lab PSU). Our main chain is XT60. Adapters are spare/lab. Not a replacement for the 12 AWG Y to the ESC.
Read next
Choice log
| What | XT60H 1→3 splitter + connector kit + XT30↔XT60 adapters |
| Why | One 6S pack in parallel to ESC, PM02D, and O4 |
| Our pick | 12 AWG XT60H Y as the pack hub. Adapters only for XT30 accessories. |
| Sources | Review panel (Oscar, Bardwell, Rosser, Painless360, UAV Tech) |
Photos